Showers

2009001 - Palm-tree shower

2009001

Dimensions product:

Height excl. leaf:           155,00 cm / 61,02 inches

Height incl. leaf:           184,00 cm / 72,44 inches  

Diameter:

Bottom tree-trunk:         ø41,00 cm / 16,14 inches

Top tree-trunk               ø16,50 cm / 6,49 inches

Top tree incl.coconuts:  ø38,00 cm / 14,96 inches

Lenght with leaf:            168,00 cm / 66,14 inches

             

Dimensions shipping carton:

 (wooden box)

Height              :           200,00 cm / 78,74 inches

Wight                :           50,00 cm / 19,68 inches

Lenght              :           50,00 cm / 19,68 inches

Packaging weight:      ±70 kg / 154 lbs

 

Complete including:

3x Showerhead. 

3x (push) taps / knobs.

3x flex water supply.

-Attention! Automatic mixing or water (pressure) control not included.

  

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

 

Important tips for installation: 

  • Let your installation be performed by a specialised installation company.
  • After mounting the product, put some putty around the product so water and dirt gets no chance to get beneath the product, also for extra Make sure that there are three connection hoses coming out of the floor with a connection of 1/2” 
  • Automatic mixing control system not included. (plam-tree only one connection for mixed water).
  • Drill the holes for the palm-tree before you install the product. Mark the holes only when the palm-tree in standing on his place.

 

Assembly procedure:

  1. Place the palm-tree on his place, over the 3 water connection hoses
  2. Mark the mounting holes on the floor through the steel plate.
  3. Take the palm-tree away and drill the holes and place plugs in the floor
  4. Place the tree back on his place and then lay the tree on it’s side so you can attach the water supply to the tree. (from the floor to the tree)
  5. Turn the palm-tree back up above the water hoses, and mount the steel plate to the floor.
  6. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

 

2008052 - Mushroom shower

2008052

Dimensions product:

Height                    :32,00 cm / 12,60 inches

Width                     :39,00 cm / 15,35 inches

Depth                     :73,00 cm / 28,74 inches

Dimensions shipping carton:

Height                    :37,00 cm / 14,57 inches

Width                     :44,00 cm / 17,32 inches

Depth                     :78,00 cm / 30,71 inches

Packaging weight:            8,30 kg / 18,26 lbs

 

Complete including:

-Showerhead chrome

-Flexible water supply 1/2” - compression fitting ø10  

-Coloured mounting screws

-Attention! Automatic mixing or water (pressure) control not included.

 

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

 

Important tips for installation: 

  • Let your installation be performed by a specialised installation company.
  • Normal height of the showerhead, for children between 3 and 9 years old is 175 to 180 cm / 68,90 to 70,87 inches,  measured from the floor.  In most cases a stage of 50cm / 19,69 inches has been placed, so parents can wash their  children on appropriate height.
  • Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
  • After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the  product, also for extra reinforcement. 
  • We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the showerhead in the product.

 

Assembly procedure:

  1. Mount the showerhead into the product, in the appropriate hole, and secure it to the back side using the supplied screw-nut.
  2. Connect the flexible hose to the showerhead.
  3. Hold the product to the wall so you can mark the 2 mounting holes on the wall.
  4. Drill the marked holes.
  5. Mount the plugs in the wall.
  6. Mount the flexible hose to the wall.
  7. Mount the product to the wall.
  8. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

2003018 - Elephant shower

2003018

Dimensions product:

Height                    :57,00 cm / 22,44 inches

Width                     :41,00 cm / 16,14 inches

Length                   :68,00 cm / 26,77 inches

Dimensions shipping carton:

Height                    :60,00 cm / 23,62 inches

Width                     :45,00 cm / 17,72 inches

Length                   :72,00 cm / 28,35 inches

Packaging weight:            10,86 kg / 23,89 lbs

 

Complete including:

-Showerhead chrome  

-Flexible water supply 1/2” - compression fitting ø10

-Coloured mounting screws

-Attention! Automatic mixing or water (pressure) control not included.

 

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

 

Important tips for installation: 

  • Let your installation be performed by a specialised installation company.
  • Normal height of the showerhead, for children between 3 and 9 years old is 175 to 180 cm 68,90 to 70,87 inches,  measured from the floor.  In most cases a stage of 50cm / 19,69 inches has been placed, so parents can wash their  children on appropriate height.
  • Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
  • After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the  product, also for extra reinforcement. 
  • We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the showerhead in the product.

 

Assembly procedure:

  1. Mount the showerhead into the product, in the appropriate hole, and secure it to the back side using the supplied screw-nut.
  2. Connect the flexible water supply to the showerhead.
  3. Hold the product to the wall so you can mark the 4 mounting holes on the wall.
  4. Drill the marked holes.
  5. Mount the plugs in the wall.
  6. Mount the flexible water supply to the wall.
  7. Mount the product to the wall.
  8. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

 

2008049 - Dragon shower

2008049

Dimensions product:

Height                    :51,00 cm / 20,08 inches

Width                     :19,00 cm / 7,48 inches

Depth                     :100,00 cm / 39,37 inches

Dimensions shipping carton:

Height                    :55,00 cm / 21,65 inches

Width                     :22,00 cm / 8,66 inches

Depth                     :104,00 cm / 40,94 inches

Packaging weight:            7,31 kg / 16,08 lbs

 

Complete including:

-Showerhead chrome

-Flexible water supply 1/2” - compression fitting ø10

-Coloured mounting screws

-Attention! Automatic mixing or water (pressure) control not included.

 

Material specification:

This product is made of 5 to 6mm thick polyester, and  is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

 

Important tips for installation: 

  • Let your installation be performed by a specialised installation company.
  • Normal height of the showerhead, for children between 3 and 9 years old is 195 to 205 cm, measured from the floor.
  • In most cases a stage of 50cm has been placed, so parents can wash their children on appropriate height.
  • Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
  • After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the  product, also for extra reinforcement. 
  • We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the showerhead in the product.

 

Assembly procedure:

  1. Mount the showerhead into the product, in the appropriate hole, and secure it to the back side using the supplied screw-nut.
  2. Connect the flexible hose to the showerhead.
  3. Hold the product to the wall so you can mark the 2 mounting holes on the wall.
  4. Drill the marked holes.
  5. Mount the plugs in the wall.
  6. Mount the flexible water hose to the wall.
  7. Mount the product to the wall.
  8. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

 

2003016 - Cloud shower

2003016

Dimensions product:

Height                    :              33,00 cm / 12,99 inches

Width                     :              17,00 cm / 6,69 inches

Length                    :              56,00 cm / 22,05 inches

Dimensions shipping carton:

Height                    :              37,00 cm / 14,57 inches

Width                     :              22,00 cm / 8,66 inches

Length                    :              60,00 cm / 23,62 inches

Packaging weight:            5,90 kg / 12,98 LBS

 

Complete including:

-Showerhead chrome  

-Flexible water supply 1/2” - compression fitting ø10

-Coloured mounting screws

-Attention! Automatic mixing or water (pressure) control not included.

 

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

 

Important tips for installation: 

  • Let your installation be performed by a specialised installation company.
  • Normal height of the showerhead, for children between 3 and 9 years old is 175 to 180 cm 68,90 to 70,87 inches,  measured from the floor.  In most cases a stage of 50cm / 19,69 inches has been placed, so parents can wash their  children on appropriate height.
  • Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
  • After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the  product, also for extra reinforcement. 
  • We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the showerhead in the product.

 

Assembly procedure:

  1. Mount the showerhead into the product, in the appropriate hole, and secure it to the back side using the supplied screw-nut.
  2. Connect the flexible water supply to the showerhead.
  3. Hold the product to the wall so you can mark the 2 mounting holes on the wall.
  4. Drill the marked holes.
  5. Mount the plugs in the wall.
  6. Mount the flexible water supply to the wall.
  7. Mount the product to the wall.
  8. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

 

pauseplay
/
show/hideshow/hide