Dimensions product:

Height                    :32,00 cm / 12,60 inches.

Width                     :56,00 cm / 22,05 inches.

Length                   :66,50 cm / 26,18 inches.

Dimensions shipping carton:

Height                    :37,00 cm / 14,57 inches.

Width                     :60,00 cm / 23,62 inches

Length                   :70,00 cm / 27,56 inches.

Packaging weight:  13,19 kg / 29,02 lbs

Complete including:

-Water tap self-closing 1/2”

-Siphon PVC

-Flexible water supply 1/2” x 3/4” and 50cm / 19,69 inches.

-Mounting screws in colour.

-Attention! Automatic mixing or water (pressure) control not included.  

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

Important tips for installation: 

• Let your installation be performed by a specialised installation company.
• Normal height of the top side of the washbowl, for children between 3 and 9 years old is 50 to 60 cm / 19,69 to 23,62  inches, measured from the floor. c to c of the drain which leaves the wall is: ±33 cm / 12,99 inches high
• Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
• After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement. 
• In case you bought a mirror in combination with this washbowl please watch out. In most cases the washbowl cannot  support the mirror because the water tap doesn’t fit underneath. Hold 10cm  / 3,94 inches space  between washbowl  and mirror. (see picture)
• We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the drain plug in the product.

Assembly procedure:

1. Separate the washbowl from the undercarriage.
2. Mount the self-closing water tap in the appropriate hole; fitting should be done from the bottom side. Take care that the black rubber ring is mounted between the tap and the product.
3. Mount the connecting hose secure to the tap at the bottom side.
4. Glue the drain plug to the washbowl with appropriate putty.
5. Hold the siphon against the bottom side of the washbowl, and then mount the screw of the siphon from above to secure.
6. Hold the undercarriage to the wall so you can mark the 2 mounting holes on the wall. (you can find the mounting holes at the inside of the undercarriage)
7. Drill the marked holes.
8. Mount the plugs in the wall.
9. Mount the undercarriage to the wall.
10. Place the washbowl back in the undercarriage and connect the siphon and water supply to the wall.
11. Attach the washbowl from the outside of the product into the wooden blocks to secure it to the under carriage.
12. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

Dimensions product:

Height                    :32,00 cm / 12,60 inches

Width                     :53,00 cm / 20,87 inches

Depth                     :51,00 cm / 20,08 inches

Dimensions shipping carton:

Height                    :37,00 cm / 14,57 inches 

Width                     :56,00 cm / 22,05 inches 

Depth                     :58,00 cm / 22,83 inches 

Packaging weight:              12,40 kg / 27,28 lbs  

Complete including:

-Water tap self-closing 1/2”

-Stainless steel washbowl ø 41  

-Stainless steel adapter ring

-Siphon PVC

-Flexible water supply 1/2” - compression fitting ø10 -Mounting screws.

-Attention! Automatic mixing or water (pressure) control not included.

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

Important tips for installation: 

• Let your installation be performed by a specialised installation company.
• Normal height of the top side of the washbowl, for children between 3 and 9 years old is 50 to 60 cm / 19,69 to 23,62  inches, measured from the floor. c to c of the drain which leaves the wall is: ±33 cm / 12,99 inches high
• Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
• In case you bought a mirror in combination with this washbowl please watch out. In most cases the washbowl cannot  support the mirror because the water tap doesn’t fit underneath. Hold 10cm  / 3,94 inches space  between washbowl  and mirror. (see picture)
• Don't tighten the screw (which is used to secure the drain plug for installation of the siphon) too hard because  otherwise the stainless steel washbowl can bow.
• After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the  product, also for extra reinforcement. 
• Put some putty around the stainless steel washbowl so water and dirt gets no chance to get behind the product.
• We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the stainless steel washbowl in the product.

Assembly procedure:

1. Mount the self-closing water tap in the appropriate hole, fitting should be done from the bottom side. Take care that the black rubber ring is mounted between the tap and the product.
2. Mount the connecting hose secure to the tap at the bottom side.
3. Glue the drain plug to the stainless steel washbowl with appropriate putty.
4. Hold the adapter ring against the bottom side of the stainless steel washbowl.
5. Mount the siphon to the bottom side of the adapter ring.
6. Mount the screw of the siphon from above, trough the drain plug to secure the ring between the drain plug and the siphon.
7. Hold the product to the wall so you can mark the 2 mounting holes on the wall.
8. Drill the marked holes.
9. Mount the plugs in the wall.
10. Glue the stainless steel washbowl with all accessories secure in the product.
11. Connect the flexible water supply and hose to the wall.
12. Mount the product to the wall with the colored mounting screws.
13. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

Dimensions product:

Height                    :75,00 cm / 29,53 inches.

Width                     :16,00 cm / 6,30 inches

Lenght                   :62,00 cm / 24,41 inches.

Dimensions shipping carton:

Height                    :85,00 cm / 33,46 inches.

Width                     :20,00 cm / 7,87 inches.

Length                   :70,00 cm / 27,56 inches.

Packaging weight:            16,00 kg / 35,20 lbs

Complete including:

Mirror glass silver-plated

Toothbrush shelf

4x coloured screws 

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water  pressure.

Important tips for installation: 

• Let your installation be performed by a specialised installation company.
• Normal height of the down side of the mirror, for children between 3 and 9 years old is 60 to 70 cm  / 23,62 to 27,56  inches, measured from  the floor.
• Screw the product securely to the wall using a rubber ring for the screw. This prevents the product may crack if you  tighten it too hard.
• After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the  product, also for extra reinforcement. 
• In case you bought a washbowl in combination with this mirror please watch out. In most cases the washbowl cannot  support the mirror because the water tap doesn’t fit directly underneath the mirror. Hold 10cm  / 3,94 inches space  between washbowl and mirror. (see picture)
• We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the toothbrush shelf to the product.

Assembly procedure:

1. Mount the toothbrush shelf underneath the product with the appropriate screw.
2. Attach the mirror to the product using a construction adhesive.
3. Mount the wooden frame in front of the mirror using the appropriate coloured screws.
4. Hold the product to the wall so you mark the 4 mounting holes to the wall.
5. Drill the mounting holes.
6. Mount the plugs in the wall.
7. Mount the product against the wall.
8. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.

Dimensions product:

Height                    :46,00 cm / 18,11 inches

Width                     :64,00 cm / 25,20 inches

Depth                     :138,00 cm / 54,33 inches

Dimensions shipping carton:

Height                    :50,00 cm / 19,69 inches

Width                     :69,00 cm / 27,17 inches

Depth                     :142,00 cm / 55,91 inches

Complete including:

-2x Water tap self-closing 1/2”

-2x Stainless steel washbowl ø 42

-2x Stainless steel adapter ring  

-2x Siphon PVC

-2x Flexible water supply 1/2” x 3/4” and 50 cm / 19,69 inches.

-Mounting screws.

-2x Mounting brackets

-Attention! Automatic mixing or water (pressure) control not included.

Material specification:

This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.

Important tips for installation: 

• Let your installation be performed by a specialised installation company.
• Normal height of the top side of the washbowl, for children between 3 and 9 years old is 50 to 60 cm / 19,69 to 23,62  inches, measured from the floor. c to c of the drain which leaves the wall is: ±33 cm / 12,99 inches high
• Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
• After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement. 
• In case you bought a mirror in combination with this washbowl please watch out. In most cases the washbowl cannot support the mirror because the water tap doesn’t fit underneath. Hold 10cm  / 3,94 inches space  between washbowl  and mirror. (see picture)
• We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the drain plug in the product.

Assembly procedure:

1. Mount the self-closing water tap in the appropriate hole, fitting should be done from the bottom side. Take care that the black rubber ring is mounted between the tap and the product.
2. Mount the connecting hose secure to the tap at the bottom side.
3. Glue the drain plug to the stainless steel washbowl with appropriate putty.
4. Hold the adapter ring against the bottom side of the stainless steel washbowl.
5. Mount the siphon to the bottom side of the adapter ring.
6. Mount the screw of the siphon from above, trough the drain plug to secure the ring between the drain plug and the siphon.
7. Hold the product to the wall so you can mark the 4 mounting holes from the mounting brackets on the wall.
8. Drill the marked holes.
9. Mount the plugs in the wall.
10. Mount the brackets to the wall and place some putty on top of the brackets.
11. Mount the product on top of the brackets with normal mounting screws (make sure the screws are not to long)
12. Glue the stainless steel washbowl with all accessories secure in the product.
13. Connect the flexible water supply and siphon to the wall.
14. After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.