Washbowls and Mirrors
2011004 - Tree-trunk washbowl
Dimensions product:
Height :53,00 cm / 20,86 inches.
Width :51,00 cm / 20,07 inches.
Length :54,00 cm / 21,26 inches.
Dimensions shipping carton:
Height :59,00 cm / 23,23 inches.
Width :56,00 cm / 22,05 inches
Length :59,00 cm / 23,23 inches.
Packaging weight: 15,43 kg / 33,95 lbs
Complete including:
-Water tap self-closing 1/2”
-Siphon PVC
-Flexible water supply 1/2” x 3/4” and 50cm / 19,69 inches.
-Mounting screws in colour.
-Attention! Automatic mixing or water (pressure) control not included.
Material specification:
This product is made of 5 to 6mm thick polyester, and
is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.
Important tips for installation:
- Let your installation be performed by a specialised installation company.
- Normal height of the top side of the washbowl, for children between 3 and 9 years old is 55 to 65 cm / 21,65 to 25,59 inches, measured from the floor. c to c of the drain which leaves the wall is: ±33 cm / 12,99 inches high
- Screw the product securely to the wall with a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement.
- In case you bought a mirror in combination with this washbowl please watch out. In most cases the washbowl cannot support the mirror because the water tap doesn’t fit underneath. Hold 10cm / 3,94 inches space between washbowl and mirror. (see picture)
- We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the drain plug in the product.
Assembly procedure:
- Mount the self-closing water tap in the appropriate hole; fitting should be done from the bottom side. Take care that the black rubber ring is mounted between the tap and the product.
- Mount the connecting hose secure to the tap at the bottom side.
- Glue the drain plug to the washbowl with appropriate putty.
- Hold the siphon against the bottom side of the washbowl, and then mount the screw of the siphon from above to secure.
- Hold the undercarriage to the wall so you can mark the 4 mounting holes on the wall. (you can find the mounting holes at the outside of the undercarriage)
- Drill the marked holes.
- Mount the plugs in the wall.
- Connect the siphon and water supply to the wall.
- Mount the undercarriage to the wall.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.
2011002 - Monkey Mirror
Dimensions product:
Height :82,00 cm / 32,28 inches
Width :20,00 cm / 7,87 inches
Depth :58,00 cm / 22,83 inches
Dimensions shipping carton:
Height :87,00 cm / 34,25 inches
Width :24,00 cm / 9,45 inches
Depth :62,00 cm / 24,41 inches
Packaging weight: 7,76 kg / 17,07 lbs
Complete including:
Mirror glass silver-plated
2x coloured screws to attach the suspension
Material specification:
This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.
Important tips for installation:
- Let your installation be performed by a specialised installation company.
- Normal height of the down side of the mirror, for children between 3 and 9 years old is 60 to 70 cm / 23,62 to 27,56 inches, measured from the floor.
- Screw the product securely to the wall using a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement.
- In case you bought a washbowl in combination with this mirror please watch out. In most cases the washbowl cannot support the mirror because the water tap doesn’t fit directly underneath the mirror. Hold 10cm / 3,94 inches space between washbowl and mirror. (see picture)
- We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the toothbrush shelf to the product.
Assembly procedure:
- Mount the toothbrush shelf underneath the product with the appropriate screw.
- Attach the mirror to the product using a construction adhesive.
- Mount the wooden frame in front of the mirror using the appropriate coloured screws.
- Hold the product to the wall so you mark the 2 mounting holes to the wall.
- Drill the mounting holes.
- Mount the plugs in the wall.
- Mount the product against the wall.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.
2011001 - Toucan mirror
Dimensions product:
Height :82,00 cm / 32,28 inches
Width :14,00 cm / 5,51 inches
Depth :56,00 cm / 22,05 inches
Dimensions shipping carton:
Height :87,00 cm / 34,25 inches
Width :18,00 cm / 7,09 inches
Depth :60,00 cm / 23,62 inches
Packaging weight: 6,35 kg / 13,97 lbs
Complete including:
Mirror glass silver-plated
2x coloured screws to attach the suspension
Material specification:
This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.
Important tips for installation:
- Let your installation be performed by a specialised installation company.
- Normal height of the down side of the mirror, for children between 3 and 9 years old is 60 to 70 cm / 23,62 to 27,56 inches, measured from the floor.
- Screw the product securely to the wall using a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement.
- In case you bought a washbowl in combination with this mirror please watch out. In most cases the washbowl cannot support the mirror because the water tap doesn’t fit directly underneath the mirror. Hold 10cm / 3,94 inches space between washbowl and mirror. (see picture)
- We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the toothbrush shelf to the product.
Assembly procedure:
- Mount the toothbrush shelf underneath the product with the appropriate screw.
- Attach the mirror to the product using a construction adhesive.
- Mount the wooden frame in front of the mirror using the appropriate coloured screws.
- Hold the product to the wall so you mark the 2 mounting holes to the wall.
- Drill the mounting holes.
- Mount the plugs in the wall.
- Mount the product against the wall.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.
2011002 - Crocodile Mirror
Dimensions product:
Height :91,00 cm / 35,83 inches
Width :26,00 cm / 10,24 inches
Depth :58,00 cm / 22,83 inches
Dimensions shipping carton:
Height :96,00 cm / 37,80 inches
Width :30,00 cm / 11,81 inches
Depth :62,00 cm / 24,41 inches
Packaging weight: 8,42 kg / 18,52 lbs
Complete including:
Mirror glass silver-plated
2x coloured screws to attach the suspension
Material specification:
This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of cleaning materials. We use the same coating on
our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.
Important tips for installation:
- Let your installation be performed by a specialised installation company.
- Normal height of the down side of the mirror, for children between 3 and 9 years old is 60 to 70 cm / 23,62 to 27,56 inches, measured from the floor.
- Screw the product securely to the wall using a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement.
- In case you bought a washbowl in combination with this mirror please watch out. In most cases the washbowl cannot support the mirror because the water tap doesn’t fit directly underneath the mirror. Hold 10cm / 3,94 inches space between washbowl and mirror. (see picture)
- We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the toothbrush shelf to the product.
Assembly procedure:
- Mount the toothbrush shelf underneath the product with the appropriate screw.
- Attach the mirror to the product using a construction adhesive.
- Mount the wooden frame in front of the mirror using the appropriate coloured screws.
- Hold the product to the wall so you mark the 2 mounting holes to the wall.
- Drill the mounting holes.
- Mount the plugs in the wall.
- Mount the product against the wall.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.
2003051 - Shield Mirror
Dimensions product:
Height :87,00 cm / 34,25 inches
Width :9,50 cm / 3,74 inches
Depth :71,00 cm / 27,95 inches
Dimensions shipping carton
Height :99,00 cm / 38,98 inches
Width :14,00 cm / 5,51 inches
Depth :92,00 cm / 36,22 inches
Packaging weight: 9,33 kg / 20,53 lbs
Complete including:
Mirror glass silver-plated
2x coloured screws to attach the suspension
Material specification:
This product is made of 5 to 6mm thick polyester, and is coated with a matt varnish. With this coating the product is resistant against all kinds of
cleaning materials. We use the same coating on our products as been used in the car industry, so you can clean our products just like a car. (do not use an abrasive sponge) Also you can clean our products with water pressure.
Important tips for installation:
- Let your installation be performed by a specialised installation company.
- Normal height of the down side of the mirror, for children between 3 and 9 years old is 60 to 70 cm / 23,62 to 27,56 inches, measured from the floor.
- Screw the product securely to the wall using a rubber ring for the screw. This prevents the product may crack if you tighten it too hard.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product, also for extra reinforcement.
- In case you bought a washbowl in combination with this mirror please watch out. In most cases the washbowl cannot support the mirror because the water tap doesn’t fit underneath. (see picture)
- We advice you to use a silicon putty for gluing around the product and use a panel and construction adhesive for gluing the toothbrush shelf to the product.
Assembly procedure:
- Hold the product to the wall so you mark the 2 mounting holes to the wall.
- Drill the mounting holes.
- Mount the plugs in the wall.
- Mount the product against the wall.
- After mounting the product, put some putty around the product so water and dirt gets no chance to get behind the product.
